Reef Explorers

Diving at altitude: mountain lakes, computers and going higher afterwards

Diving in lakes above 300 m: why lower air pressure changes decompression, setting tables and computers, and waiting before driving over passes or flying.

A lake high in the mountains looks like any other dive site, but the lower air pressure at the surface changes your decompression. Diving above about 300 metres means adjusting your planning, and the same physics matters when you drive or fly higher after diving.1,2

What counts as altitude diving

Altitude diving is usually defined as diving where the surface is 300 metres (980 ft) or more above sea level. DAN explains why the threshold exists: standard dive tables are designed for a particular altitude range, usually 1,000 feet (about 300 m) above sea level or less.1,2

Higher up, the air pressure at the surface is lower. DAN gives the example of a dive at 2,000 feet, where surface pressure is 0.93 atm. This affects the decompression requirement of a dive, because when you surface the barometric pressure is lower than at sea level.1,2

Tables and dive computers

Dive table and computer algorithms are based on sea level and calculated for seawater, while most altitude dives are in fresh water, which is less dense than the seawater used to build decompression tables. DAN notes that a variety of tables allow you to convert your usual dive planner for an altitude dive.1,2

Many dive computers have a pressure sensor that reads the air pressure when you switch them on at the site. DAN points out a drawback: the computer senses only where you are, not where you came from, so it may not account for the ascent you made to reach the lake. A computer without a sensor has to be set to the altitude by hand, and either way you also need to set it to fresh or salt water.2

Arriving at the lake

Travelling up to the dive site is itself a change in altitude. DAN notes that after ascending to a higher site you may need to treat your first dive as a repetitive dive. DAN's general advice is to plan a conservative profile, stay well within the limits of your planning device and allow for a safety stop.2

Driving over passes or flying after diving

Going higher after a dive works like flying after diving. DAN says it is generally best to avoid altitude exposure, whether by ground travel or by flying, soon after diving. Its flying-after-diving guidelines recommend a minimum surface interval of 12 hours after a single dive within no-decompression limits and 18 hours after multiple days of diving; DAN Europe gives the same figures, with 18 hours after repetitive dives or multiple days of diving.3,4

Sources differ on when a road trip counts. The DAN guidelines cover exposure altitudes between 2,000 and 8,000 feet (610 to 2,438 m) and ignore changes of less than 2,000 feet. DAN Europe considers a post-dive altitude change of more than about 700 m to carry the same risk as flying, and says the most prudent choice is to wait 24 hours before flying or going to high altitude. Check the height of any pass on your route home before the last dive.3,4

Before you go

  • Find out the altitude of the lake and use altitude tables or a computer set for it.1,2
  • Set your computer to fresh water.1,2
  • Allow for the climb to the site; your first dive may count as a repetitive dive.2
  • Plan conservatively and include a safety stop.2
  • Plan the route home so you do not cross high passes or fly too soon after diving.3,4
  • For questions about your own risk, ask a dive physician or DAN.3

Sources

  1. 1. en.wikipedia.org
  2. 2. dan.org
  3. 3. dan.org
  4. 4. alertdiver.eu

Sources checked on 10 November 2026. Written from these pages and checked by an independent second reader.

Where to dive next month

One email a month, around the 25th: the destinations in season the following month, with their sources, an article to read and an instructor's tip. Free, no ads.

Your address is only used to send this newsletter, through MailerLite. Every email has an unsubscribe link. Your data and your rights